By DTF OneStop Team. Last updated October 28, 2026.
Quick answer: For most shops, a double-sided, hot-peel (instant-peel) PET film is the easiest choice. You press, wait a few seconds and peel while it's still warm, so the press keeps moving. Pick the film width that matches your printer (12–13in for A3 printers, 24in for 60cm printers), and pair it with a fine powder for detailed artwork on tees or a medium powder for heavier fabrics like hoodies. Store film and powder sealed, in a cool, dry room.
Peel types explained
The "peel" is when, and at what temperature, you pull the PET carrier off after pressing.
| Peel type |
When you peel |
Finish (typical) |
Good for |
| Hot peel / instant peel |
Right after pressing, while warm, often within seconds |
Usually matte |
Fast production, high volume |
| Warm peel |
After a short cool-down |
Between the two |
Shops that find hot peel too touchy |
| Cold peel |
After the transfer has cooled fully |
Often glossier |
Some fine-detail work; slower |
"Instant peel" is a marketing term most sellers use for hot-peel film that releases within a few seconds. Our film pages list press at 300°F, peel in about 3 seconds. Always follow the press time and pressure your film, powder and garment call for, and test on a scrap garment first. More background: Hot peel vs cold peel.
Single-sided vs double-sided film
-
Single-sided film has a coating only on the print side. It's usually cheaper but can curl or slip, especially in humid shops or long runs.
-
Double-sided film has a matte coating on the back too. That helps the film feed flat and stay put on the platen or rollers and grip the powder evenly.
Every DTF film roll we list is double-sided, hot peel.
Matching film width to your printer
| Film (all double-sided hot peel) |
Roll size |
Fits |
Stock (10/28/2026) |
| 12in |
12in × 328ft (30cm × 100m) |
A3 printers with 12in media width, e.g. the Audley A3 DTF
|
In stock |
| 13in |
13in × 328ft (33cm × 100m) |
13in-class printers (the Audley A3 prints up to 12in) |
In stock |
| 16in |
16in × 984ft (40cm × 300m) |
40cm-class printers |
In stock |
| 17in |
17in × 328ft (43cm × 100m) |
43cm-class printers |
In stock |
| 24in |
24in × 328ft (60cm × 100m) |
All Audley 24in (60cm) 2/4/6-head printers |
In stock |
| 32in |
32in × 328ft (81cm × 100m) |
80cm-class printers |
In stock |
All widths in one place: DTF transfer film. The 24in roll also comes with A8 or Audley logo markings; the product page says the marking is for identification only and it's the same film.
Load film that matches the printer's media width. Narrower film wastes print width, and wider film won't feed.
Hot-melt powder: fine vs medium
DTF powder is a thermoplastic adhesive (typically TPU-based) that sticks to the wet ink and melts into the fabric under the press.
| Grade |
Particle size (per our product page) |
Use it for |
| Fine |
80–170µm |
Detailed art, small text, thin lines, lightweight tees; softer hand feel |
| Medium |
100–200µm |
Hoodies, heavier cotton, canvas, high-volume runs where grip matters more than softness |
Our Premium DTF Hot Melt Powder is white, in 1kg bags. It comes in Fine (80–170µm) and Medium (100–200µm) grits; check the product page for current availability of each.
Applying it: an automatic shaker spreads powder, shakes off the excess and cures it in one pass. On A3 setups you can powder by hand and cure in an oven or with a hovering heat press. Either way, cure until the powder looks melted and smooth (orange-peel texture), not grainy and not bubbled. Cured powder gives off fumes, so ventilate and follow the OEM manuals.
Storage and humidity
-
Film: keep it sealed in its bag, standing upright or hanging, away from sunlight and heaters. Humid air makes film curl and the coating absorb moisture. That leads to ink pooling or "fisheye" spots.
-
Powder: keep the bag sealed between uses. Damp powder clumps and spreads unevenly. Don't store it next to the shaker's exhaust.
-
Room conditions: our cleaning and capping solution pages list 50–70% RH and 75–80°F as a working environment for the printer. Keep film and powder sealed, cool and dry.
A quality checklist for any DTF film or powder
Use this on our rolls or anyone else's:
-
Flatness: does the film lie flat on the platen for the whole roll?
-
Ink hold: are edges sharp, with no bleeding or beading?
-
Even coating: no streaks or bare patches when you hold it up to the light.
-
Clean release: does it peel the way the label says (hot, warm or cold) without leaving ink on the film?
-
Powder coverage: powder sticks only to the ink, and the excess shakes off clean.
-
Wash test: press a test shirt and wash it several times before you sell that combination.
-
Consistency: first roll vs fifth roll. Note your lot numbers.
FAQ
What's the difference between hot peel and cold peel DTF film?
Hot-peel film is peeled while the transfer is still warm, usually within seconds, and gives a matte finish. Cold-peel film is peeled after it cools fully, which is slower and often glossier.
Is instant peel film the same as hot peel?
In practice, yes. "Instant peel" usually describes hot-peel film that releases a few seconds after pressing. Our rolls list a 300°F press and about a 3-second peel.
What width DTF film do I need?
Match your printer's media width: 12–13in for A3 printers, 24in for 60cm printers like the Audley 2-, 4- and 6-head models.
Fine or medium DTF powder?
Fine for detail and soft hand feel on tees. Medium for heavy fabrics and maximum grip.
Do you sell gold DTF film?
We don't stock a gold PET DTF film right now. For metallic effects we carry Gold TPU transfer film (for UV printers, on fabric) and UV DTF gold foil film (for the 8074-3).
Sources
- DTF film product pages (sizes, double-sided matte, 300°F / ~3s hot peel, stock rechecked 2026-10-28): dtfonestop.com/products/dtf-transfer-film and the 12in, 13in, 16in, 17in, 24in and 32in roll pages
- Powder (Fine 80–170µm, Medium 100–200µm, 1kg, white): dtfonestop.com/products/premium-dtf-hot-melt-powder-superior-adhesion-for-long-lasting-vibrant-prints
- Audley A3 media width conflict: dtfonestop.com/products/audley-a3-dtf-printer-2-head-xp600
- Environment figures: dtfonestop.com/products/dtf-capping-solution-for-dtf-printhead-wet-capping
- Existing hot vs cold peel post: dtfonestop.com/blogs/news/understanding-dtf-film-hot-peel-vs-cold-peel
- Crawl index: /workspace/content/assets/website-dtfonestop.md (2026-10-18)